Download

Model for Blade nano cpx, with timer, idle up and throttle hold.

Used with home made dsm2/x module.

Download

Helicopter template for FBL helicopter.

4 Flightmode, Throttle hold, Normal and idleup 1 and 2.

Trippel rate, shared switch for Travel limit and Expo for Aileron, Elevator and Rudder.

Timer for total flight time and battery.

Download

Setup T-Rex 550L Futaba SBUS style, setup with Brain / Icon Flybarless system 

Download

T-Rex 450L setup Futaba SBUS style, BRAIN / ICON Flybarless System

Download

Configuration designed to work with DSMX module (example tested with ORX DSM2/DSMX Module with push button selectable protocols) in 22ms DSMX (two flashes) mode. All flight modes implemented (stability, 3D/acro, safe) with throttle and pitch curves approximating recommended settings. Expo/Rates for Aileron, Elevator, Rudder set to switch.

Download

This is a base working CCPM eepe for the Trex 500 Electric. You may have to adjust your curves but it is a good base.

Download

Helicopter with normal Swash plate. Throttle Cut - Flight Mode Throttle Hold with Throttle hold Delay - Flight Mode Normal (When 15% of stick governor enable at 1600 rpm) - Flight Mode Idle Up1 (governor enable at 1800 rpm)- Flight Mode Idle Up2 (governor enable at 1900 rpm). Governor On Off switch - Gyro On Off switch (Normal - AVCS). Fail safe all return to center.

Download

Basic setup (Normal + Idle-Up1 + Idle-Up2) for Horizon Hobby Blade 130X based on the default values described in the user guide. Read the detailed description for the switch description.
This is an OpenTX 2.1 version.

Download

Taranis X9E with X6R connected by SBUS to V-Stabi 5.2

Download

I'm putting this out there hopefully to help. It is my eePe file for my Taranis Plus, X8R and Ikon setup. I am also using version 2.1.7. I have not flight tested yet due to waiting for parts. But a bench test showed everything working.

Download

Thunder Tiger Raptor 30 v1 with OS .37 engine and Futaba GY401 gyro.  

Download

Miniature Aircraft X-Cell Helicopter with OS .46, Futaba GY401 Gyro.

Download

I've been flying my Gaui X3 with this configuration for quite some time now and it flies great.

Download

T-Rex 450 SE with Futaba 401 gyro.  CCPM configured helicopter.

Download

Blade 180 CFX

Download

Hey!

I've made a profile for my XK 110 and taranis with multimodule.

Curves copied from original manual.

There are 3 modes: Normal, Idle 70% and Idle 100%.

I use OpenTX 2.2.0, be aware.

Download

OpenTX 2.2 model for Blade 180CFX

Configured as per Blade 180CFX manual with AUX2 programming.

Download

This is a Flybarred Trex 500 for Taranis running OpneTX 2.2.

Download

Setup for Blade 270 Fusion with an Orange module.

Download

Specifically for 200SRX (fixed pitch)

SE - Mode
SF - Thottle hold
SG - DR/Expo (low/medium/high)
SH - Rescue

Throttle based timer - 5 Mins

Voice Alerts on all mode changes

PPM tuned for Orange PPM module.

Download

Synergy E5

SBUS (Futaba Channel Order) with BD3SX

SH:  Captain Rescue

LS:  Volume Control

S1: Self-level

S2:  Tail Gain Adjustment

SE / SB:  Flight Modes (4 Flight Modes + Normal

SC: High, Middle, Low Rates 

AMP and Voltage telemetry sensors

Download

Gaui X3

SBUS (Futaba Channel Order) with BD3SX

SH:  Captain Rescue

LS:  Volume Control

S1: Self-level

S2:  Tail Gain Adjustment

SE / SB:  Flight Modes (4 Flight Modes + Normal

SC: High, Middle, Low Rates 

AMP and Voltage telemetry sensors

Download

Trex 450 heli with flymentor.

I included my soundfiles for FM postionmode FM balance mode FM off. as well as the other files i use for flightmode normal flightmode idle up and so on.

Download

Hurricane Helicopter settings. FM phases (Hover, Trans and Acro)(SE), with throttle stick block (SF) and Cut glow engine with full closed carburetor (SH). Gyro connect and disconnect (SC). 

Enjoy It.

P.D. Voices in Spanish

Download

Basic setup (Normal + Idle-Up1) for T-Rex 500 ESP with Flybar.
Futaba Setup.