![]() |
![]() |
![]() |
![]() |
Category: Lua Scripts | ||
![]() ![]() |
|
GPS Heading calculation script. |
Created Size Downloads |
2014-07-19 4.8 KB 2674 |
||
![]() ![]() |
|
![]() ![]() |
|
![]() |
Created Size Downloads |
2017-04-26 0 B 3858 |
||
![]() ![]() |
|
![]() ![]() |
|
This script calculates models ascend/descend rate in m/min. |
Created Size Downloads |
2015-11-09 2.07 KB 2593 |
||
![]() ![]() |
|
Script to "lag" a source. Collects source and returns it later. set source required. Set delay required in times - 1 to 100 in steps of approx 30milliseconds. |
Created Size Downloads |
2014-08-20 549 B 2363 |
||
![]() ![]() |
|
![]()
|
Created Size Downloads |
2014-09-21 10.6 KB 2458 |
||
![]() ![]() |
|
![]() LuaPilot is a nice Telemetry Created |
2015-10-29 71.1 KB 10247 |
||
![]() ![]() |
|
![]() ![]() |
|
![]() ![]() |
|
![]() Modified #2 Lua from OpenTX website. It only requires TX + RX and FLVS (voltage) sensor.Created |
2014-08-21 923 B 2973 |
||
![]() ![]() |
|
![]() OpenLUA-plane - OpenTx 2.2 - Taranis X9d+ |
Created Size Downloads |
2019-06-24 715.1 KB 1296 |
||
![]() ![]() |
|
![]() ![]() |
|
This telemetry script monitors some key values concerning electric powered aircraft. It is telem7 for my use and must be in /SCRIPTS/modelname/telem1-to-7 USE THE DATA WITH CAUTION!
|
Created Size Downloads |
2014-08-03 6.49 KB 2537 |
||
![]() ![]() |
|
![]() This one-time script help you to calculate the Center of Gravity (COG) of your airplane. |
Created Size Downloads |
2014-08-29 1.09 MB 3154 |
||
![]() ![]() |
|
![]() This srcipt alert you when the distance of your airplane and a GPS point is less than a distance. |
Created Size Downloads |
2014-09-03 176.53 KB 1829 |
||
![]() ![]() |
|
SayAlt is a simple mix script to announce Altitude as the aircraft passes through the chosen altitude increments, either passing Up or Down. It assumes the Taranis is using the FrSky Altimeter. The script watches for the altitude transition and triggers a Logical Switch which then triggers a Special Function to make the voice announcement. |
Created Size Downloads |
2017-02-24 4.6 KB 1935 |
||
![]() ![]() |
|
This Mix script, called secursw.lua, creates an unKnockable safety like the one described by MattyB, a two position switch from a three position switch to be used where you want a control which cannot be inadvertantly activated by a bump. It is a simple but interesting introduction to Lua script programming. |
Created Size Downloads |
2016-10-29 1.76 KB 1758 |
||
![]() ![]() |
|
![]() Was Change Sensor Id. Lua script to change Frsky sensor configuration from the radio (ported from erskyTx. Thanks to MikeB)
|
Created Size Downloads |
2019-06-18 14.24 KB 2239 |
||
![]() ![]() |
|
use switch H to play sounds in a sequence, each time it is pulled next sound file in list is played, long press resets. 1.3 updated to allow changing to logical switches by altering one small line of script. 1.2 updated ready for opentx 2.1 update 1.1 repeats cycle and is layed out different;y using a single line for input of sound files. can be a function lua .... |
Created Size Downloads |
2014-08-16 1.19 KB 2611 |
||
![]() ![]() |
|
This gives you up to 6 independent switches which can be toggled in sequence by 2 switches.
|
Created Size Downloads |
2019-05-29 31.61 KB 1293 |
||
![]() ![]() |
|
![]() ![]() |
|
![]() A updated more customisable user-friendly version of the original Simple Background Music Player. |
Created Size Downloads |
2016-01-29 491.81 KB 2869 |
||
![]() ![]() |
|
By Nigelsheffield. Just a simple stop watch shows current time and last time and speaks the lap time as switch H is pulled and resets and carries on timing next lap. Gives spoken to 10th sec lap time and a screen record to 1/100th. use switch H but easily changed in script with a text editor. version 1.1 gives longer run time and uses minutes .... |
Created Size Downloads |
2014-10-22 1.05 KB 2087 |
||
![]() ![]() |
|
Smooth channel by Lua Script Description not finish |
Created Size Downloads |
2014-10-01 8.18 KB 1819 |
||