![]() |
![]() |
![]() |
![]() |
Category: Helicopters | ||
![]() ![]() |
|
![]() Skyartec Wasp 100 Nano CP |
Created Size Downloads |
2013-06-24 76.03 KB 2243 |
||
![]() ![]() |
|
![]() Bavarian Demon BD3SX FBL Unit with Futaba Channel Order (Using SBUS) Bailout on SH Sticky Throttle Hold |
Created Size Downloads |
2014-01-03 77.03 KB 2340 |
||
![]() ![]() |
|
Synergy E5 SBUS (Futaba Channel Order) with BD3SX SH: Captain Rescue LS: Volume Control S1: Self-level S2: Tail Gain Adjustment SE / SB: Flight Modes (4 Flight Modes + Normal SC: High, Middle, Low Rates AMP and Voltage telemetry sensors |
Created Size Downloads |
2014-08-05 77.03 KB 2872 |
||
![]() ![]() |
|
T-Rex 450 SE with Futaba 401 gyro. CCPM configured helicopter. |
Created Size Downloads |
2016-12-26 77.03 KB 4616 |
||
![]() ![]() |
|
Trex 450 heli with flymentor. I included my soundfiles for FM postionmode FM balance mode FM off. as well as the other files i use for flightmode normal flightmode idle up and so on. |
Created Size Downloads |
2014-05-11 1.16 MB 3871 |
||
![]() ![]() |
|
![]() T-Rex 450L setup Futaba SBUS style, BRAIN / ICON Flybarless System |
Created Size Downloads |
2015-12-06 76.03 KB 4357 |
||
![]() ![]() |
|
![]() Setup T-Rex 550L Futaba SBUS style, setup with Brain / Icon Flybarless system
|
Created Size Downloads |
2015-12-06 76.03 KB 3656 |
||
![]() ![]() |
|
Taranis X9E with X6R connected by SBUS to V-Stabi 5.2 |
Created Size Downloads |
2016-01-25 77.03 KB 3308 |
||
![]() ![]() |
|
I've been flying my Gaui X3 with this configuration for quite some time now and it flies great. |
Created Size Downloads |
2016-12-26 77.03 KB 2769 |
||
![]() ![]() |
|
Thunder Tiger Raptor 30 v1 with OS .37 engine and Futaba GY401 gyro.
|
Created Size Downloads |
2016-10-01 77.03 KB 3152 |
||
![]() ![]() |
|
This is a base working CCPM eepe for the Trex 500 Electric. You may have to adjust your curves but it is a good base.
|
Created Size Downloads |
2015-11-11 77.03 KB 5051 |
||
![]() ![]() |
|
This is a Flybarred Trex 500 for Taranis running OpneTX 2.2. |
Created Size Downloads |
2017-12-31 917 B 2724 |
||
![]() ![]() |
|
v911 |
Created Size Downloads |
2014-04-06 77.03 KB 2675 |
||
![]() ![]() |
|
v912 |
Created Size Downloads |
2014-04-06 77.03 KB 2449 |
||
![]() ![]() |
|
![]() BLHeli brushless WLToys V922 or Turnigy FBL100 |
Created Size Downloads |
2013-06-24 76.03 KB 2469 |
||
![]() ![]() |
|
This is a basic template for a stock V922 with external HT8/HT6 module plugged in the trainer port. SC controls the idle-up. In the top position it is idle-down. SC middle or down is idle-up.
It has sticky throttle-cut and once the throttle-cut has been applied then SC must be set in the up position and the throttle must be zero to release. |
Created Size Downloads |
2014-02-25 76.03 KB 2187 |
||
![]() ![]() |
|
![]() ![]() |
|
![]() WLToys V911 |
Created Size Downloads |
2013-06-24 76.03 KB 2825 |
||
![]() ![]() |
|
Hey! I've made a profile for my XK 110 and taranis with multimodule. Curves copied from original manual. There are 3 modes: Normal, Idle 70% and Idle 100%. I use OpenTX 2.2.0, be aware. |
Created Size Downloads |
2017-09-25 1.13 KB 4307 |
||